Muller Beltex is a service supplier of high-quality components for elevators. We help you to secure the mechanical side of your elevator. An important next step in this process is monitoring to make sure continuity is guaranteed. Considering an elevator is an enclosed system, knowing what is going on inside the elevator is a must. After all, prevention is the better cure. Both preventive and curative measures must be taken to ensure full and safe monitoring. To guarantee this, Muller Beltex offers a total solution with “fail safe” products it has developed and engineered itself along with external components to be able to supply a complete elevator in conformity with the latest ATEX directives. Muller Beltex’ monitoring systems oversee the entire production process thus ensuring a sustainable, problem-free bulk processing and optimum reliability. Product overview * Belt misalignment monitoring * Bearing temperature monitoring * Speed monitoring * Junction boxes, controllers, indicators & transmitters * Level instruments * Data acquisition & SCADA systems * Explosion vent panels & flameless…

Minimise maintenance with our high-quality sifter cleaning balls. Where rubber sifter cleaning balls fail over time, our Karolee® polyurethane sifter balls continuously stay active with a very long service life. These sifter balls have a lasting elasticity of 70% and are without adhesion or absorption of the processed product and are bacteriological safe. Because of these properties they comply with the most stringent requirements and regulations in the food and chemicals industry. Opt for optimum production. Do you want to know what more we can do for your installation? Please do not hesitate to contact us for more information. [AHREF**SW**mullerbeltex.com/wp-content/uploads/2017/07/ENG_datasheet_Karolee_PU_sifter_cleaning_balls.pdf**Download technical datasheet] [AHREF**SW**mullerbeltex.com/wp-content/uploads/2017/07/ENG_FDA_statement_Karolee_PU_sifter_cleaning_balls.pdf**Download FDA statement]

Kryptile ceramic liners combine the properties of aluminium oxide ceramics with the huge impact resistance and toughness of Kryptane polyurethane. Ceramic material is highly abrasion-resistant, but is vulnerable for breaking due to impact at an angle of of 90/60°. The impact energy is not absorbed and the ceramic could crack. Kryptile ceramic liners combine the properties of aluminium oxide ceramics with the huge impact resistance and toughness of Kryptane polyurethane. This protects the very fragile ceramic against a direct impact at an angle of 90/60° and is ideal for impact situations with large quantities of sharp and coarse product. This is the ultimate solution for aggressive applications. Kryptile liners are all designed in line with the customer’s requirements and can be supplied in the exact shape of, for example, a chute, bin or hopper and ensure a perfect fit. This prevents unnecessarily long installation downtime. The standard panel dimensions can be supplied in the exact dimension of 300 x 300 mm. This includes a cast steel plate with welded nut. The so-called Redi-Liners are fitted at the place…

The elevator belt in combination with the belt clamps is the most important part of a bucket elevator and is exposed to different conditions during operation. Heavy duty industry demands the utmost performance of components used in elevators. Higher loads, longer center distances, higher temperatures and tough applications require specific knowledge, a different approach and innovative solutions. Wear in the elevator The elevator belt is the heart of the elevator. All the additional items that will be fitted on the belt like elevator buckets, bolts and belt fasteners are in sense foreign objects to the belt, which in the long run could result into stress and wear, due to the pressure of these parts while running over the pulleys. Every elevator belt will first develop wear and tear in those areas where these foreign objects are attached to the belt, whether the application is hot or cold. To avoid such premature wear, in particular in the cement industry, the belt should have a maximum temperature resistance and all items attached to the belt should be as light as possible. Once a belt is aging due to affection of heat,…

Muller Beltex’s monitoring systems monitor all critical components of transport and process installations and thus guarantee explosion-proof and reliable handling of bulk materials in almost all industrial sectors. As a service supplier of high-quality systems and components for, among others, elevators, belt conveyors and screening installations, Muller Beltex ensures that these systems meet all technical requirements. The company also provides solutions to continuously monitor the condition. and operation of equipment to ensure the continuity of production processes. Also wear-resistant coverings contribute to safe and sustainable processes. Elevators For the monitoring of elevators, Muller Beltex presents in-house developed fail-safe systems as well as third-party products. This allows end users to ensure trouble-free and safe transport, while also fully complying with Atex directives. Belt misalignment monitoring One example is the Rub-Block-based belt misalignment monitoring system with a Pt100 temperature sensor. When a misalignment occurs, the belt will run against the RubBlock (a brass rubbing plate), causing its temperature to rise. If the temperature rises above…

For summer time maintenance, Muller Beltex prepares an inspection report with recommendations taking into account urgencies and the available budget. Many concrete mixing plants perform maintenance on their installations during the construction holiday. They aim to bring their plants back up to date so as to optimise performance in terms of capacity, as well as the service life of wear components. Muller Beltex is regularly involved in this and first conducts an on-site inspection that in detail reviews the product overshoot area’s, chutes and bunkers, as well as the abrasion-resistant Kryptane® liners to determine whether it is due for replacement. The result is an inspection report with recommendations that also considers urgencies and the available budget. That the elevator becomes dirty is a common occurrence, but there also is a great deal of wear and tear on the: – Steel elevator parts – Bucket elevator belt – Elevator buckets – Elevator’s inlet and outlet – Pulleys and pulley lagging Based on the inspection report, Muller Beltex looks after the maintenance, assembly and installation,…

Overhaul makes elevator better than ever. Muller Beltex has worked for IGMA for many years and is jointly responsible for the installations. The work we performed Elaborate inspections of the technical components of one of the floating weighing towers, a 36 MT crane with a capacity of 1500 MT/hour. The report showed that certain components required action in order to guarantee reliability; preventive and corrective maintenance. Belt replacement Wear on the back of the bucket elevator belt was observed making the belt’s replacement a necessity. This was also true for the rubber pulley lagging of both drive pulleys. The crowning of the return pulleys, which was too much, exerted unnecessarily high forces and friction on the belt, as well as on the belt fastener and elevator buckets. Proper planning By preparing a suitable and thorough action plan, with a realistic time span for implementing the inspection report’s recommendations, it was decided to carry out the various activities in a single efficient stop. The existing belts and both drive pulleys were hoisted to the lower deck using a telescopic…

Inspection revealed that the elevator belt was due for replacement, and it needed new wear plates. This work was carried out in a single stop to prevent many unnecessary standstills. Codrico Rotterdam BV recently told us its elevator used for the intake of raw materials was behaving erratically. Wear of the pulley’s lagging was putting the elevator belt out of alignment, so that the misalignment monitoring system issued constant alarms. Closer inspection revealed that the elevator belt was due for replacement, and it needed new wear plates. All this work was combined and the assembly was carried out in a single stop to prevent many unnecessary standstills. Activities progress The drive pulley and the elevator belt were lifted from the elevator together. The first assembly team could then disassemble the elevator buckets, which were still in good condition. The buckets were able to be attached to the new belt immediately because the new elevator belt had already been punched and delivered. Meanwhile the new NBR pulley lagging was applied at the plant’s workshop in Pijnacker in the Netherlands. This type of rubber is highly suitable for…

Solid partners join forces and consolidate expertise and know-how. Muller Beltex BV, V.A.V. Aandrijvingen BV and Germany based Bechtel GmbH have announced their strategic alliance. By a transfer of shares, the owners Lars Muller and Emiel Schoutsen have established this cooperation. The know-how and expertise in components for bulk handling equipment is not limited to the Netherlands and Germany, where the three companies are located. They operate worldwide and the close cooperation between the three companies will therefore provide major benefits for their entire, geographically widespread, customer base. Both owners emphasize that this alliance is not a merger and that the companies will retain their own identities. Company locations and contact points will remain unchanged. The advantages arising from the collaboration are, in particular, the bundling of their expertise and the use of each other’s network, especially abroad. In certain markets or geographic regions, the one partner is better represented than the other.…

For an optimal design and use of an elevator, the elevator belt and the drive and return pulleys are of crucial importance. Elevator belt In ensuring optimal and safe bulk transport, the elevator belt is of crucial importance. This is the heart of the machine and during production it is subject to various loads. Therefore, it is important that all components that come into contact with the elevator belt are carefully selected to ensure maximum service life. Drive and return pulleys In this respect, drive and return pulleys are very important components. They are constructed to suit the elevator belt and the kind of product that is being processed. From drive pulleys and cage pulleys to wing pulleys: our engineers take care of the entire process, from drawing to implementation to guarantee that the elevator belt runs properly and smoothly on the pulleys. Special attention is paid to the crowning of the drive pulley surface, construction strength, shaft connection and static balancing to realize an optimum service life for your elevator belt along with the best production result. Drum…

Spaansen Bouwsystemen in Harlingen has achieved significant cost savings with a complete elevator overhaul. Processing is more efficient and long lasting, durable components are used. Spaansen Bouwsystemen in Harlingen produces precast concrete structures. An essential conveyor in the production process is the belt elevator, which processes raw materials such as sand and gravel to the concrete mix plant. An extensive inspection by the Muller Beltex team revealed that this elevator was not sufficiently reliable. Over time, the abrasive minerals had caused a lot of wear and fouling, which meant that the continuity of providing the plant with raw materials could no longer be guaranteed. Return pulley The investigation learned that both the drive pulley and the return pulley had to be replaced. This operation has been carried out not just substituting components but by implementing notable improvements, increasing the durability of the elevator. The return pulley (lower drum) has been replaced by an open wing pulley with cone in the middle. Because of the wings and cone, product getting stuck between the elevator belt and the pulley is better taken…

Lightweight, fluffy materials can be difficult to handle in bucket elevators at high speeds. Venting an elevator bucket aids in bucket fill and discharge. Venting an elevator bucket aids in bucket fill and discharge with light, fluffy materials. Lightweight, fluffy materials, and those that are extremely dense or flow poorly can be difficult to handle in bucket elevators at high speeds. Higher filling of buckets Because these materials tend to trap air when being handled by an elevator bucket, it is necessary to provide air relief to assist in their filling and discharge. Materials in this category might be various flours, meals, feed mash or screenings. As these materials enter the bucket, air is released through a series of vent holes in the bottom of the bucket allowing for a more complete fill. These vent holes also allow air to re-enter the bucket, which facilitates full release of product into the discharge. Standard hole diameter is equal to the size of the bolt mounting holes. Anything different is considered a custom vent. Also for dense materials A venting bucket can improve the efficiency of some bucket…

This Polyurethane magnetic patch or liner can be installed quickly and safely without the use of welders or bolt fastening systems. Our products are made of high quality polyurethane and can be applied to any steel surface which have been proven to increase wear life, reduce down time and increase efficiency. Not only do these liners require no-bolt, no-glue or welding, they are also custom fit to each application so there is no cutting involved for the customer. All that is needed is a clean steel surface. Kryptane® Urethane magnetic wear liners * Constructed with Kryptane® Polyurethane * Imbedded High strength rare earth magnets allow for installation using magnetic force alone * No Bolting – No Welding – No Cutting to the applied area * Eliminates the need for Hot Work permits in most areas * Stay securely in place on vibrating screens and chutes * Can be repositioned easily and safely, when time permits, for the repair to be done permanently * Can be field trimmed to fit unusual surfaces or conditions, due to the polyurethane material * Custom Size Available Upon Request Redure…

Cost savings through elevator overhaul Spaansen Bouwsystemen in Harlingen has achieved significant cost savings with the complete overhaul of its elevator. Besides a more efficient transport, the mechanical systems are now equipped with long lasting, durable components. The extensive project was carried out by Muller Beltex. Spaansen Bouwsystemen in Harlingen produces precast concrete structures. An essential conveyor in the production process is the belt elevator, which transports building materials such as sand and gravel to the concrete plant. An extensive inspection by the Muller Beltex team revealed that this elevator was not sufficiently reliable. Over time, the abrasive minerals had caused a lot of wear and fouling, which meant that the continuity of the bulk transport could no longer be guaranteed. Return pulley The investigation learned that both the drive pulley and the return pulley had to be replaced. This operation has been carried out not just substituting components but by implementing notable…

urethane magnetic wear liners Our products are made of high quality polyurethane and can be applied to any steel surface which have been proven to increase wear life, reduce down time and increase efficiency. Not only do these liners require no-bolt, no-glue or welding, they are also custom fit to each application so there is no cutting involved for the customer. All that is needed is a clean steel surface. This Polyurethane magnetic patch or liner can be installed quickly and safely without the use of welders or bolt fastening systems. KRYPTANE® Urethane magnetic wear liners •Constructed with Kryptane® Polyurethane •Imbedded High strength rare earth magnets allow for installation using magnetic force alone •No Bolting – No Welding – No Cutting to the applied area •Eliminates the need for Hot Work permits in most areas •Stay securely in place on vibrating screens and chutes •Can be repositioned easily and safely, when time permits, for the repair to be done permanently •Can be…

Muller Beltex regularly performs inspections on bucket elevators Inspection of wheat elevator to prevent stoppages Muller Beltex regularly performs inspections on elevators in order to monitor their status. By carrying out inspections, we can prevent many stoppages caused by calamities. After completing an inspection, we draw up an extensive report explaining the situation to the client. This is followed by a comprehensive quote including a work plan describing what actions are required. Based on a phased plan, the actions are performed in a controlled way and all associated risks are identified to ensure that the work is performed safely. During this inspection of a wheat elevator, for example, a tower crane was needed to replace the drive roller. The inspection was performed while the drive roller at the top of the elevator was being replaced. Eventually, the elevator belt will need replacing during the second half of this year due to drying out. We can then replace the worn fasteners on the belt at the same time. The photos…

Rub-Block with a PT100 temperature sensor Belt misalignment monitoring – Sensors for conveyors and bucket elevators Our own product Rub-Block with a PT100 temperature sensor is designed to report the misalignment of a conveyor belt or elevator belt. The advantage of the Rub-Block is the fact that it will send a continuous output signal to the PLC. We also offer other brands belt misalignment monitoring solutions such as the well-known product Watchdog produced by 4B. Please involve us at an early stage so we can offer you the right solution for your specific issue.

Polysur® 275 K NBR elevator belt Flame-retardant NBR elevator belt increases safety in elevator The demand for safety in and around the elevator is an issue subject to adaptations of the relative applicable directives. Statistics describe the elevator as one of the most hazardous pieces of equipment because of real risk of explosion. 30-40 percent of dust explosions involve elevators. An enclosed system combined with the conveying of flammable bulk material, oxygen and possible ignition sources explain this risk of explosion. Research has shown that this can be prevented and damage can be effectively limited with various preventive and curative process monitoring systems. To prevent the spread of fire and further limit the risk of explosion one can opt for an antistatic ISO 284 and flame-retardant ISO 340 (= DIN–K-) elevator belt. In addition to our Polysur® types 272 and 278, which are already flame-retardant and own other properties, we’ve extended our range of conventional elevator…

Maxi-Ultra elevator belt fastener The Maxi-Ultra elevator belt fastener is a Muller Beltex engineered and developed product which is fitted with a replaceable NBR or heat resistant wear part on the aluminium wedge section. The rubber part wears down rather than the surface of the elevator belt. This increases the safety in the clamp fastener. Maxi-Ultra is widely applicable for several types of belt in the Polysur range (belt thickness «10 mm) because of the radius in the belt fastener. This product is lighter then other fastener from our product portfolio. All things considered, the fastener makes a substantial contribution to increasing the lifespan of the elevator belt.

We proudly present our new website. With its new identity, the website reflects the amazing dynamism of the industries we serve and provides easy access to our products, services and documentation. Our new website is totally modern with every facility. For example, it is responsive and therefore compatible with mobile devices like smartphones and tablets. It also has links to social media allowing you to share any interesting information or inspiration immediately. As an organisation for which quality and customer focus are key, we felt we needed a new website which really reflected these important aspects. This website allows you to search effectively for the information you need in two languages, it is easy to navigate and you will have access to even more available know-how and services. If you can’t find certain information, our team will be happy to help you find the right solution to your specific issue.

Rub-Block with a PT100 sensor The Rub-Block RB200DN with a PT100 temperature sensor is designed to report the misalignment of a conveyor or elevator belt. The advantage of the Rub-Block is the fact that it will send a continuous output signal to the PLC. The Rub-Block emits a permanent life standby signal. If such a signal is absent, this must be investigated and if required the PT100 sensor must be replaced. As long as the Rub-Block emits a standby signal, it will also emit an emergency contact signal caused by its temperature rising, as soon as a belt touches it. Off-tracking belts running into the side of conveyor equipment will cause friction, which may cause damage to the belt, and may generate heat, fire, or a dust explosion. The Rub-Block is very easy to install, it will be fitted on both sides of a conveyor or elevator belt. Once the belt off-tracks and runs onto the brass plate of the Rub-Block, it will create friction and the temperature of the Rub-Block brass plate increases.…

Muller Beltex POLYSUR® type 272 white NBR-FDA rubber elevator belts are fully conform U.S. Food and Drug Adm. Reg. and are super oil and fat resistant as well anti-static acc. to ISO 284. Suitable for handling any food stuff up to 80° C. Belts in strength classes 500 N/mm 3-ply (350 PIW) and 630 N/mm 4-ply (450 PIW) can be supplied ex stock complete with machine punched bolt holes. A full range of black NBR elevator belts up to 1000 N/mm 5-ply (600 PIW), metal and plastic buckets, bolts and clamps is available in stock.

Muller Beltex of The Netherlands and UK have recently introduced a needle felt material called Polyveyor which is specially designed for use in air slides, fluidising discs and cones, and as aeration pads, particularly in the cement industry. Traditional air flow belts are usually of a solid woven construction. This type of belt can have hot spots caused by uneven air flow through the weave, leading to lack of fluidity and reduced capacity. Polyveyor gives an even air distribution to ensure a good cushion for a consistent flow with virtually no abrasion wear. Unlike solid woven belts, Polyveyor does not need to have the edges heat or silicone sealed to prevent air loss, and the needle felt material is easy to cut and drill for flange fitting. Extensive testing by Spoornet Transwerk (South African Railways) for their cement applications has proved that Polyveyor not only gives consistently good flow rates, but has shown no particulate infiltration to retard the…